Spectrum-controls 1769sc-HART Modules Bedienungsanleitung Seite 59
- Seite / 176
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 6: Module Data, Status, and Configuration
User’s Manual 0300217-03 Rev. A
6-7
Note: Not all controllers support this function. Refer to your controller’s user manual
for more details.
SV0...SV3 (Slot Variables 0 to 3)
Enables HART slot variables 0 through 3 for the selected channel.
Note: Slot variables are not supported by all HART devices.
Note: Slot codes must be enabled in sequential order. For example, SV0 (Enabled),
SV1 (Disabled), and SV2 (Enabled), is not a valid configuration. In this case, all three
slot variables would be enabled.
Reserved
Must be set to Zero
EC (Enable Channel)
This bit allows the user to enable or disable the channel.
6.3.13 Channel X
1
Output Type and Data Format (Words 1, 9, 17, 25)
This section of the configuration allows the user to define the output type (i.e. 0 to 20mA
or 4 to 20 mA) and the data format for the associated channel. See table below.
Table 6-4 (Output Type and Data Format)
1514131211109876543210
0 to 20mA
000
4 to 20mA
001
Reserved
Set To Zero
00000
Raw /Proportional
000
Engineering Units
001
Scaled for PID
010
Percent Range
011
Reserved
Set To Zero
00000
To Select
Make these bit settings
Output Type
Data Type
Output Type
Allows the user to configure the output type and range for the associated channel.
Note: To enable HART you must select the 4 to 20 mA range.
Reserved
Reserved for future expansion and should be set to zero.
- Compact™ I/O 1
- Isolated HART 1
- Analog Module 1
- Table of Contents 3
- Preface 7
- Conventions 8
- Used in This 8
- Chapter 1 9
- Module Overview 9
- Section 1.3 10
- Hardware 10
- Features 10
- Section 1.4 11
- System 11
- 1.4.1 System Operation 11
- Section 1.5 12
- Module 12
- Operation 12
- Chapter 2 13
- Quick Start for Experienced 13
- Chapter 3 19
- Installation and Wiring 19
- 3.3.3 Remove Power 21
- 3.3.4 Selecting a Location 21
- 3.5.2 Panel Mounting 24
- 3.7.2 Terminal Door Label 26
- 3.7.5 Wiring the Module 27
- 1.1.6 Wiring Diagram 28
- 3.7.7 Calibration 28
- Chapter 4 29
- Configuring the OF4IH for 29
- CompactLogix Using 29
- RSLogix 5000 29
- Section 4.4 36
- Project Tags 36
- Project 37
- Figure 4-11 (Output Tags) 39
- Section 4.5 40
- Sample Project 40
- Chapter 5 43
- Configuring the OF4IH for a 43
- MicroLogix 1500 Using 43
- RSLogix 500 43
- Section 5.3 48
- Using the 48
- Ladder Sample 48
- Chapter 6 53
- Module Data, Status, and 53
- Channel Configuration 53
- Configuration 56
- 6.3.12 Channel X 57
- 6.3.13 Channel X 59
- 6.3.20 Pad (Word 32) 62
- Chapter 7 67
- Enabling and Using HART on 67
- Table 7-1 (HART Packet 0) 71
- Table 7-2 (HART Packet 1) 72
- Figure 7-4 (Packet Ladder) 75
- 7.2.3 Packet Interval 76
- Section 7.3 77
- Sending 77
- Messages 77
- 7.3.3 Processing a Message 79
- Figure 7-6 Sending Message 80
- Figure 7-7 Receiving Message 81
- Figure 7-8a (Message Ladder) 82
- Figure 7-9b 83
- Figure 7-9c 84
- Figure 7-9d 85
- Figure 7-9e 86
- Figure 7-9f 87
- Figure 7-9g 88
- Figure 7-9h 89
- Figure 7-9i 90
- Figure 7-9j 91
- Figure 7-9k 92
- Figure 7-9l 93
- Figure 7-11b 102
- Figure 7-11c 103
- Figure 7-11d 104
- Figure 7-11e 105
- Section 7.5 107
- HART Protocol 107
- Overview 107
- 7.5.1 Message Format 107
- Attention 113
- Figure 8-7b 115
- 8.2.1 MAIN Routine 117
- 8.2.2 PACKETS Routine 118
- Figure 8-6b 119
- Figure 8-6c 120
- 8.2.3 MSG_TO_MOD Routine 121
- Figure 8-7c 123
- Figure 8-7d 124
- Figure 8-7e 125
- Figure 8-7f 126
- Figure 8-7g 127
- Figure 8-7h 128
- Figure 8-7i 129
- Figure 8-7j 130
- Figure 8-7k 131
- Figure 8-7l 132
- Figure 8-7m 133
- Figure 8-7n 134
- Figure 8-7o 135
- Figure 8-7p 136
- Figure 8-7q 137
- 8.2.4 SRC_CHECK Routine 138
- Figure 8-8b 139
- 8.2.5 DEST_CHECKSUM Routine 140
- Figure 8-9b 141
- 8.2.6 HART_MSG Routine 142
- Figure 8-10b 143
- Figure 8-10c 144
- Figure 8-10d 145
- Figure 8-10e 146
- Figure 8-10f 147
- Figure 8-10g 148
- Figure 8-10h 149
- Figure 8-10i 150
- Figure 8-10j 151
- Figure 8-10k 152
- 8.2.7 WORD_BYTE Routine 153
- Figure 8-11b 154
- Figure 8-11c 155
- 8.2.8 HART_CHECK Routine 156
- Figure 8-12b 157
- 8.2.9 BYTE_WORD Routine 158
- Chapter 9 161
- Diagnostics and 161
- Troubleshooting 161
- 1514131211109876543210 163
- 0000000000000000 163
- Section 9.7 165
- Error Codes 165
- Section 9.8 165
- Inhibit Function 165
- Appendix A 167
- Module Specifications 167
- 0C < Ta < 60C 168
- DEMKO 11 ATEX 1103437X 168
- IIC T4 Gc 168
- Appendix B 169
- HART Universal and Common 169
- Practice Commands 169
- Getting Technical 175
- Assistance 175
- Declaration of 175
- Conformity 175
Verwandte Produkte und Handbücher für Messgeräte Spectrum-controls 1769sc-HART Modules
(126 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.017 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern